Supported coding options

Air conditioning on in AUTO mode

Enable/disable the automatic activation of the air conditioning when the AUTO mode is turned on.

Values:

• Active
• Not active

Requirements:

• “Air Conditioning” IHKA_R57 or “Air Conditioning” IHKA_R56 or “Air Conditioning” IHKA_R60 control unit

Angel Eyes parking light brightness

The brightness of the Angel Eyes when the parking light is turned on.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Auto Start Stop function memory

Save the last used Auto Start Stop function setting for the next start of the car. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

Values:

• Active
• Not active

Requirements:

• “Smart Power Electronics Gateway” SPEG or “Air Conditioning” IHKA_R60 control unit

Battery type

The type and capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

Values:

• 46 Ah
• 55 Ah
• 60 Ah AGM
• 70 Ah
• 70 Ah AGM
• 80 Ah
• 80 Ah AGM
• 90 Ah
• 90 Ah AGM
• 105 Ah AGM
• 110 Ah

Requirements:

• “Car Access System” CAS3 control unit

Check Control notification brake force display

Enable/disable the Check Control notification for the brake force display.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification brake light

Enable/disable the Check Control notification for the brake light.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification fog lights

Enable/disable the Check Control notification for the fog lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification front parking lights

Enable/disable the Check Control notification for the front parking lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Check Control notification front turn signals

Enable/disable the Check Control notification for the front turn signals.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification high beam

Enable/disable the Check Control notification for the high beam.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification inner tail lights

Enable/disable the Check Control notification for the inner tail lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Check Control notification interior lights

Enable/disable the Check Control notification for the interior lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification license plate lights

Enable/disable the Check Control notification for the license plate lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification lights

Enable/disable the Check Control notification that is displayed when the driver door is opened and the lights are still turned on.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Check Control notification low beam

Enable/disable the Check Control notification for the low beam.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification outer tail lights

Enable/disable the Check Control notification for the outer tail lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Check Control notification parking lights

Enable/disable the Check Control notification for the parking lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification rear left fog light

Enable/disable the Check Control notification for the rear left fog light.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification rear right fog light

Enable/disable the Check Control notification for the rear right fog light.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification rear turn signals

Enable/disable the Check Control notification for the rear turn signals.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification reversing lights

Enable/disable the Check Control notification for the reversing lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Check Control notification third brake light

Enable/disable the Check Control notification for the third brake light.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Cancel coming home lights

The coming home lights are turned off when the high beam lever is pulled a second time.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Coming home lights

Enable/disable the Coming home lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Coming home lights duration

The lighting duration of the lights when Coming home lights are activated.

Values:

• 40 seconds
• 90 seconds
• 150 seconds
• 240 seconds
• Off

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Coming home lights with remote control

Activate coming home lights by pushing the button to open the trunk on the remote control twice.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM3_R56 control unit

Extend Coming home lights

The lighting duration of the coming home lights is extended when the high beam lever is pulled a second time.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Convenient closing

Enable/disable the convenient closing. During convenient closing the windows are closed and the power folding mirrors are folded in. To trigger convenient closing the lock button on the remote control has to be pressed and held. Please note that this option does not work for convertibles.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Convenient closing delay

The delay for the convenient closing before the windows are closed.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• No delay

Requirements:

• “Car Access System” CAS3 control unit

Convenient closing delay front windows

The delay at which the front windows are closed during convenient closing.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• 2 seconds
• 2.5 seconds
• 3 seconds
• 3.5 seconds
• No delay

Requirements:

• “Car Access System” CAS3 control unit

Convenient closing delay sunroof

The delay as of with the sunroof is closed during convenient closing.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• 2 seconds
• 2.5 seconds
• 3 seconds
• 3.5 seconds
• 6 seconds
• No delay

Requirements:

• “Car Access System” CAS3 control unit

Convenient closing with Comfort Access

Enable/disable the convenient closing with the Comfort Access. For convenient closing with the Comfort Access the door handle has to be touched and held at the ribbed surface. Please note that this option does not work for convertibles.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Convenient closing with remote control

Enable/disable the convenient closing with the remote control. For convenient closing with the remote control, the lock button has to be pressed and held. Please note that this option does not work for convertibles.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Convenient opening

Enable/disable the convenient opening. During convenient opening the windows are opened and the power folding mirrors are unfolded. For a convenient opening the unlock button on the remote control has to be pressed and held. When using Comfort Access, the door handle has to be gripped and held.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Convenient opening delay

The delay for the convenient opening before the windows are opened.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• 2 seconds
• 2.5 seconds

Requirements:

• “Car Access System” CAS3 control unit

Convenient opening delay rear windows

The delay at which the rear windows are opened during convenient opening.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• 2 seconds
• 2.5 seconds
• 3 seconds
• 3.5 seconds
• No delay

Requirements:

• “Car Access System” CAS3 control unit

Convenient opening delay sunroof

The delay as of with the sunroof is opened during convenient opening.

Values:

• 0.5 seconds
• 1 second
• 1.5 seconds
• 2 seconds
• 2.5 seconds
• 3 seconds
• 3.5 seconds
• 6 seconds
• No delay

Requirements:

• “Car Access System” CAS3 control unit

Convenient opening with remote control

Enable/disable the convenient opening with the remote control. For convenient opening with the remote control, the unlock button has to be pressed and held.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Daytime running light fog lights

Use the fog lights as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Daytime running light fog lights brightness

The brightness of the fog lights when used as daytime running light.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM3_R56 control unit

Daytime running light high beam brightness

The brightness of the dimmed high beam when used as daytime running light.

Values:

• Off
• Very low
• Low
• Medium
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Daytime running light inner tail lights

Use the inner tail lights as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM3_R56 control unit

Daytime running light lower brake lights

Use the lower brake lights as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Daytime running light side markers

Use the side markers as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM3_R56 control unit

Daytime running light tail lights brightness

The brightness of the tail lights when used as daytime running light.

Values:

• Off
• Very low
• Low
• Medium
• High
• Very high

Requirements:

• “Footwell Module” FRM3_R56 control unit

Daytime running light turn signals front

Use the front turn signals as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Daytime running light upper brake lights

Use the upper brake lights as daytime running light. Please note that “Daytime running light used lights” has to be set to “Additional lights only”.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Daytime running light used lights

The lights that are used for the daytime running light.

Values:

• Off
• Low beam
• Dimmed high beam
• Additional lights only (EU)
• Additional lights only (US)

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Digital speed correction

Enable/disable the correction of the digital speedometer.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Digital speed in board computer

Enable/disable the display of the digital speed in the board computer. Please toggle the displayed information in the board computer with the button in the turn signal lever until the specific display appears.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Empty menu item in board computer

Enable/disable the empty menu item in the board computer.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Speedometer correction

Enable/disable the speedometer correction.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Automatic lock time

The car is locked again automatically after it has been unlocked and no door has been opened.

Values:

• Not active
• 1 minute
• 2 minutes
• 5 minutes
• 10 minutes

Requirements:

• “Car Access System” CAS3 control unit

Easy access

If the car is unlocked pushing the unlock button on the remote control twice, the driver door window is lowered when the door is opened.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Lock doors automatically

The doors are locked automatically when reaching the set speed.

Values:

• 2 km/h
• 4 km/h
• 8 km/h
• 16 km/h
• 24 km/h
• 32 km/h
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Lock with ignition on

The doors are locked automatically when the ignition is turned on.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Open the rear window with button in footwell

Open the rear window instead of the trunk with the button in the footwell.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Rear window open with button outside

Open the rear window instead of the trunk lid with the button outside.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Rear window open with remote control

Open the rear window instead of the trunk lid with the remote control.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Selective central locking

Only the driver door is opened when the unlock button on the remote control is pressed once. When the button is pressed a second time all doors are unlocked.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Unlock doors automatically

The doors are unlocked automatically when the key is removed. Please note that this only works if the doors have been locked automatically before.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Window lifter interruption when opening a door

Enable/disable the window lifter interruption when a door is opened.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Window lifters deactivation with engine start

Enable/disable the interruption of the window lifters when the engine is started.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Window lifters deactivation with ignition off

The window lifters are deactivated after the time set after the ignition has been turned off.

Values:

• 1 minute
• 2 minutes
• 5 minutes
• 10 minutes
• 15 minutes

Requirements:

• “Car Access System” CAS3 control unit

Window lifters deactivation with opening door

The window lifters are deactivated after the ignition is turned off and the driver door is opened.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Bi-xenon flasher

Enable/disable the flasher using bi-xenon.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Turn off fog light with flasher

Turn of the fog light automatically as long as the flasher is activated.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Remaining range warning

The remaining range at which the range warning is activated.

Values:

• 10 kilometers
• 20 kilometers
• 30 kilometers
• 40 kilometers
• 50 kilometers
• 100 kilometers
• Off

Requirements:

• “Instrument Cluster” KOMB56 control unit

Reserve warning

The remaining fuel at which the reserve warning is activated.

Values:

• 6.5 litres
• 8 litres
• 10 litres
• 12.5 litres
• 20 litres

Requirements:

• “Instrument Cluster” KOMB56 control unit

Fade in/out interior lighting

The interior lighting is faded in/out.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Turn off Interior lighting after two minutes

Turn off interior lighting after two minutes automatically.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Comfort Start

Enable/disable the Comfort Start function. With Comfort Start enabled the START-STOP button has to be pushed briefly only once to start the engine.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Comfort key eject

Enable/disable the ejection of the key when start-stop button is pressed and held.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

LED conversion Brake Force Display

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion brake light

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion center brake light

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion fog lights

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion front standing lights/Angel Eyes

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 control unit

LED conversion front turn signal

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion high beam

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion inner tail lights

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion interior lights

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 control unit

LED conversion license plate light

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion low beam

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion outer tail lights

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion position lights

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM3_R56 control unit

LED conversion rear fog light

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion rear turn signals

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion reversing light

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

LED conversion side turn signal

Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding if needed after it has been applied.

Values:

• Active

Requirements:

• “Footwell Module” FRM3_R56 control unit

Corner LEDs

Enable/disable the corner LEDs.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Corner LEDs brightness with high beam

The brightness of the corner LEDs when the high beam is turned on.

Values:

• Off
• Low
• Medium
• High

Requirements:

• “Footwell Module” FRM3_R56 control unit

Corner LEDs brightness with low beam

The brightness of the corner LEDs when the low beam is turned on.

Values:

• Off
• Low
• Medium
• High

Requirements:

• “Footwell Module” FRM3_R56 control unit

Fog lights off with high beam

The fog lights are turned off automatically when the high beam is activated.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Interior lighting with remote control

The interior lighting is turned on when the button to lock the car on the remote control is pressed after it has been locked.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Parking lights brightness

The brightness of the parking lights.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 control unit

Standing lights brightness with high beam

The brightness of the standing lights with the high beam turned on.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 control unit

Standing lights brightness with low beam

The brightness of the standing lights with the low beam turned on.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 control unit

US sidemarker brightness

The brightness of the US sidemarkers.

Values:

• Off
• Very low
• Low
• Medium
• High
• Very high

Requirements:

• “Footwell Module” FRM2_R56 control unit

Automatic mirror tilt

Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Fold mirrors with convenient closing

Enable/disable mirror folding with convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Panic alarm activation time

The duration that the button to open the trunk on the remote control has to be pressed until the panic alarm is triggered.

Values:

• 1 second
• 2 seconds
• 5 seconds

Requirements:

• “Car Access System” CAS3 control unit

Panic alarm duration

The panic alarm duration if it is not cancelled using the remote control.

Values:

• 1 minute
• 5 minutes
• 10 minutes
• 15 minutes
• Unlimited

Requirements:

• “Car Access System” CAS3 control unit

Panic alarm with remote control

The panic alarm is triggered when the button to open the trunk on the remote control is pressed and held. Please note that the car has to be equipped with an alarm system and the “Panic alarm” option in the “Anti-theft alarm system” control unit has to be enabled also.

Values:

• Active
• Not active

Requirements:

• “Car Access System” CAS3 control unit

Initial seat belt reminder after start

Activate/deactivate the initial acoustic seat belt reminder after the car is started.

Values:

• Active
• Not active

Requirements:

• “Airbag Control Unit” MRS6 control unit

Seat belt reminder driver seat

Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.

Values:

• Active
• Not active

Requirements:

• “Airbag Control Unit” MRS6 control unit

Seat belt reminder passenger seat

Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.

Values:

• Active
• Not active

Requirements:

• “Airbag Control Unit” MRS6 control unit

Alarm system activation/deactivation

Enable/disable the alarm system with the remote control or a key. For theft prevention it may be beneficial to allow deactivation of the alarm system with the remote control only.

Values:

• With key or remote control
• With remote control only

Requirements:

• “Car Access System” CAS3 control unit

Comfort Access deactivation

Disable the Comfort Access for theft prevention. Please note that this requires the key to be inserted to start the engine. Use a backup to revert this coding if needed after it has been applied.

Values:

• Deactivated

Requirements:

• “Car Access System” CAS3 control unit

Double pulse hazard flasher

Enable/disable the double pulse hazard flasher.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Flash when locking

Enable/disable the flashing when the car is locked.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Flash when unlocking

Enable/disable the flashing when the car is unlocked.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

One-touch turn signal duration

The duration of the one-touch signal.

Values:

• 1 time
• 3 times
• 5 times

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Turn signals front lamp

Values:

• Bulb
• LED

Requirements:

• “Footwell Module” FRM3_R56 control unit

Turn signals rear lamp

Values:

• Bulb
• LED

Requirements:

• “Footwell Module” FRM3_R56 control unit

US sidemarker brightness

The brightness of the US sidemarkers.

Values:

• Off
• Very low
• Low
• Relatively low
• Medium
• Relatively high
• High
• Very high

Requirements:

• “Footwell Module” FRM3_R56 control unit

US sidemarkers

Enable/disable the US style sidemarkers using the turn signals or separate lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Low beam cold monitoring

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 control unit

Ignition key warning

Enable/disable the ignition key warning

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Speed limit warning

A warning is displayed if the set speed limit is exceeded.

Values:

• 120 km/h
• 190 km/h
• 210 km/h
• 240 km/h
• Off

Requirements:

• “Instrument Cluster” KOMB56 control unit

Temperature warning

Enable/disable the temperature warning.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” KOMB56 control unit

Welcome Light lighting duration

The lighting duration of the Welcome Light.

Values:

• 5 seconds
• 10 seconds
• 20 seconds
• 30 seconds
• 60 seconds

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights

Enable/disable the Welcome Lights.

Values:

• Active
• Not active

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights brake lights

The brake lights are turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights fog lights

The fog lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights front turn signals

The front turn signals are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights high beam

The high beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights license plate lights

The license plate lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights low beam

The low beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights parking lights front

The front parking lights are turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights parking lights rear

The rear parking lights are turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights rear fog light

The rear fog light is turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights sidemarkers

The sidemarkers are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit

Welcome Lights third brake light.

The third brake light is turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM3_R56 control unit

Welcome Lights turn signals front

The front turn signals are turned on with the Welcome Lights.

Values:

• Hard on
• Off
• Soft on

Requirements:

• “Footwell Module” FRM2_R56 or “Footwell Module” FRM3_R56 control unit