Supported coding options

Acoustic pedestrian protection in parking mode

Enable/disable the acoustic pedestrian protection in parking mode.

Values:

• Active
• Not active

Requirements:

• “Receiver Audio Module” RAM control unit

Acoustical lock/unlock confirmation

Enable/disable the acoustical confirmation when the car is locked/unlocked.

Values:

• Active
• Not active

Requirements:

• “Roof Function Center” FZD__35 control unit

Checkbox acoustical lock confirmation

Enable/disable the checkbox in the settings for doors/keys in the iDrive system to enable/disable the acoustical lock confirmation. If the checkbox in the iDrive system does not allow selection, please check if “Acoustical lock/unlock confirmation” in the “Roof Function Center” control unit is set to “Active“ also. Please note that the car has to be equipped with an alarm system.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Confirmation sound duration

The duration of the confirmation sound that is played when locking/unlocking the car.

Values:

• Short
• Normal
• Long
• Very long

Requirements:

• “Roof Function Center” FZD__35 control unit

Confirmation sound frequency

The frequency of the confirmation sound that is played when locking/unlocking the car.

Values:

• Low
• Normal
• High

Requirements:

• “Roof Function Center” FZD__35 control unit

Confirmation sound volume

The volume of the confirmation sound that is played when locking/unlocking the car.

Values:

• Low
• Normal
• High
• Very high

Requirements:

• “Roof Function Center” FZD__35 control unit

Active Sound Design

Enable/disable the Active Sound Design. Please note that it is not possible to enable the Active Sound Design for cars that are not equipped with this option by factory. If the coding has no effect, then please also deactivate the ASD activation code (select “Receiver Audio Module” control unit > select “Activation codes” at the bottom of the screen > select “01B4 - Active Sound Design” > “Deactivate“.

Values:

• Active
• Not active

Requirements:

• “Receiver Audio Module” RAM control unit

Alarm sound

The alarm sound that is played when the alarm is triggered.

Values:

• Alarm sound Europe
• Alarm sound Great Britain
• Alarm sound USA

Requirements:

• “Roof Function Center” FZD__35 control unit

Interior motion detection

Enable/disable the interior motion detection of the alarm system. Please note that this function requires the car to be equipped with an alarm system.

Values:

• Active
• Not active

Requirements:

• “Roof Function Center” FZD__35 control unit

OBD alarm

The alarm is triggered when the vehicle is locked and communication via the OBD port is detected. Please note that this function requires the car to be equipped with an alarm system.

Values:

• Active
• Not active

Requirements:

• “Roof Function Center” FZD__35 control unit

Ambient lighting color

The color of the ambient lighting in the interior for the color setting “Bronze”.

Values:

• Bronze
• Red
• Orange
• Yellow
• Yellow-green
• Green
• Green-cyan
• Cyan
• Cyan-blue
• Blue
• Blue-magenta
• Magenta
• Magenta-red

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Bowers & Wilkins sound settings

With the Bowers & Wilkins sound settings, extended sound presets are activated in the settings in the iDrive system under “Sound“. Please note that these only have an effect if a Harman Kardon sound system is installed in the vehicle. Use a backup to revert this coding once it has been applied.

Values:

• Active

Requirements:

• “Headunit” HU_MGU control unit

Maximum volume at start-up

The maximum volume that is saved when the iDrive system is shut off and restored automatically on the next start-up.

Values:

• 10%
• 20%
• 25%
• 30%
• 40%
• 50%

Requirements:

• “Headunit” HU_MGU control unit

Ready-to-drive sound

A sound is played when the vehicle is ready to drive.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Ready-to-drive sound type

The sound that is played when the vehicle is ready to drive. The “Ready-to-drive sound“ may also have to be activated in the “Body Domain Controller“ additionally.

Values:

• Alternative
• Default

Requirements:

• “Receiver Audio Module” RAM control unit

Signal tones

Change the sounds for various functions (warning chime, PDC, turn signals, telephone ringtone).

Values:

• BMW
• BMW 2021
• MINI
• Rolls-Royce

Requirements:

• “Receiver Audio Module” RAM control unit

Auto Start Stop function

Enable/disable the Auto Start Stop function.

Values:

• Active
• Not active

Requirements:

• “Engine Control Unit” DME control unit

Auto Start Stop function memory

Save the last used Auto Start Stop function setting for the next start of the car. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

Values:

• Active
• Not active

Requirements:

• “Engine Control Unit” DME control unit

Battery capacity

The capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

Values:

• 20 Ah
• 50 Ah
• 60 Ah
• 69 Ah
• 70 Ah
• 80 Ah
• 90 Ah
• 105 Ah

Requirements:

• “Engine Control Unit” DME control unit

Battery type

The type of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

Values:

• AGM
• EFB
• Lead acid
• Lithium-ion

Requirements:

• “Engine Control Unit” DME control unit

Brake Force Display activation brake force

The brake deceleration at which the Brake Force Display is activated.

Values:

• Weak braking (5 m/s²)
• Medium braking (7 m/s²)
• Hard braking (8 m/s²)

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Brake Force Display activation speed

The speed at which the Brake Force Display is activated.

Values:

• 5 km/h
• 10 km/h
• 20 km/h
• 30 km/h
• 40 km/h
• 50 km/h

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Checkbox daytime running light

Enable/disable the checkbox in the lighting settings in the iDrive system to turn the daytime running light on or off.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Cover Artwork

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Start animation

The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

Values:

• Default
• BMW
• M variant 1
• ALPINA
• BMW i
• Rolls Royce

Requirements:

• “Headunit” HU_MGU control unit

Tire pressure control

The displayed values of the tire pressure control in the iDrive system. Please note that the car has to be equipped with the required sensors to make this work.

Values:

• Display pressure only
• Display temperature and pressure
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Volume popup

Enable/disable the volume popup that is displayed when the volume is changed.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Diesel logo

Enable/disable the Diesel logo.

Values:

• Active
• Not active

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Fuel consumption display maximum value

The maximum value of the fuel consumption display.

Values:

• 15 l/100km
• 20 l/100km
• 30 l/100km

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Layout

Change of layout in the instrument cluster. Please note that the layouts are not fully compatible with hybrid vehicles.

Values:

• ALPINA
• M
• M Performance up to 160 mph
• M Performance up to 200 mph
• M Sport
• Standard

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Refresh rate digital speed

The refresh rate for the digital speed display in the instrument cluster.

Values:

• 2 times per second
• 5 times per second

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Tire widget

Display tire pressures and temperatures in the instrument cluster.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Horn signal when locking the car with engine running

Enable/disable the horn signal that sounds when locking the car with the engine running.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Lock after pulling away

Enable/disable the “Lock after pulling away“ checkbox in the settings in the iDrive system in the car.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Time until automatic lock

The car is locked automatically again if it has been unlocked and no door has been opened within the set time.

Values:

• 10 seconds
• 30 seconds
• 1 minute
• 2 minutes
• 5 minutes
• 10 minutes

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Window lifter interruption when opening a door

Enable/disable the window lifter interruption when a door is opened.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Default driving mode

The standard driving mode that is activated when the car is started.

Values:

• ADAPTIVE
• COMFORT
• COMFORT INDIVIDUAL
• COMFORT+
• ECO PRO
• ECO PRO INDIVIDUAL
• ECO PRO+
• ELECTRIC
• ELECTRIC INDIVIDUAL
• HYBRID
• HYBRID ECO
• SPORT
• SPORT (Hybrid)
• SPORT INDIVIDUAL
• SPORT INDIVIDUAL (Hybrid)

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Low fuel warning 1

The remaining range at which the permanent low fuel warning is displayed.

Values:

• 10 kilometers
• 10 miles
• 20 kilometers
• 20 miles
• 30 kilometers
• 30 miles
• 40 kilometers
• 50 kilometers
• Not active

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Low fuel warning 2

The remaining range at which the temporary low fuel warning is displayed.

Values:

• 40 miles
• 50 kilometers
• 50 miles
• 60 kilometers
• 70 kilometers
• 80 kilometers
• 90 kilometers
• Not active

Requirements:

• “Instrument Cluster” DKOMBI4 control unit

Automatic light control

The lighting switch position where the automatic light control is active. To prevent the low beam to come on when the switch is set to “0”, use the option “Active in position A”.

Values:

• Active in position A
• Active in position A and 0

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Exterior lighting switch-off allowed

Allow the exterior lights to be turned off when the engine is running.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Fog lights off with high beam

Enable/disable the automatic switch-off of the fog lights when the high beam is turned on.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Fog lights with parking lights

Allows the fog lights to be turned on with parking lights.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Hazard warning signal after emergency braking

The hazard warning signal is activated automatically after an emergency braking.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rain-light-sensor sensitivity

The sensitivity of the rain-light-sensor that affects the automatic wiper and light activation.

Values:

• Insensitive
• Normal
• Sensititve
• Very sensitive

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Automatic mirror tilt

Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors. Make sure the button in the door for selecting the mirror is set to the driver side also.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Automatic mirror tilt value

The tilt value of the right mirror, when the reverse gear is engaged.

Values:

• 10%
• 20%
• 30%
• 40%
• 50%
• 59 %
• 60%
• 63 %
• 70%
• 71 %
• 72 %
• 80%
• 90%
• 91 %
• 93 %
• 100%

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Fold mirrors with convenient closing

Enable/disable the folding of the mirrors when using convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Steering wheel heating automatic activation (2 of 2)

The iDrive system can be used to set the steering wheel heating to be activated automatically below a certain outside temperature. The option “Steering wheel heating automatic activation (1 of 2)“ must also be activated in the “Headunit“.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Unfold mirrors with convenient opening

Enable/disable the unfolding of the mirrors when using convenient opening.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

One-touch turn signal 5 times

Enable/disable the “5 times” one-touch turn signal option in the exterior lighting settings in the iDrive system.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

PDC/Top View distance switch-off threshold

The driven distance after the PDC is turned off automatically.

Values:

• 10 m
• 20 m
• 30 m
• 40 m
• 50 m
• 100 m
• 150 m
• 200 m
• 250 m

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

PDC/Top View speed switch-off threshold

The speed at which the PDC and the Top View is turned off automatically.

Values:

• 5 km/h
• 10 km/h
• 15 km/h
• 20 km/h
• 30 km/h
• 35 km/h
• 40 km/h
• 50 km/h

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear view camera distance switch-off threshold

The driven distance after the rear view camera is turned off automatically.

Values:

• 10 m
• 20 m
• 30 m
• 40 m
• 50 m
• 100 m
• 150 m
• 200 m
• 250 m

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear view camera speed switch-off threshold

The speed at which the rear view camera is turned off automatically.

Values:

• 5 km/h
• 10 km/h
• 14 km/h
• 15 km/h
• 20 km/h
• 30 km/h
• 36 km/h
• 40 km/h
• 50 km/h

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front backrests temperature level 1

The temperature of the front backrests for seat heating level 1.

Values:

• 30 °C
• 31 °C
• 32 °C
• 33 °C
• 34 °C
• 35 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front backrests temperature level 2

The temperature of the front backrests for seat heating level 2.

Values:

• 36 °C
• 37 °C
• 38 °C
• 39 °C
• 40 °C
• 41 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front backrests temperature level 3

The temperature of the front backrests for seat heating level 3.

Values:

• 42 °C
• 43 °C
• 44 °C
• 45 °C
• 46 °C
• 47 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front seats temperature level 1

The temperature of the front seats for seat heating level 1.

Values:

• 30 °C
• 31 °C
• 32 °C
• 33 °C
• 34 °C
• 35 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front seats temperature level 2

The temperature of the front seats for seat heating level 2.

Values:

• 35 °C
• 36 °C
• 37 °C
• 38 °C
• 39 °C
• 40 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Front seats temperature level 3

The temperature of the front seats for seat heating level 3.

Values:

• 41 °C
• 42 °C
• 43 °C
• 44 °C
• 45 °C
• 46 °C
• 47 °C
• 48 °C
• 49 °C
• 50 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear backrests temperature level 1

The temperature of the rear backrests for seat heating level 1.

Values:

• 30 °C
• 31 °C
• 32 °C
• 33 °C
• 34 °C
• 35 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear backrests temperature level 2

The temperature of the rear backrests for seat heating level 2.

Values:

• 36 °C
• 37 °C
• 38 °C
• 39 °C
• 40 °C
• 41 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear backrests temperature level 3

The temperature of the rear backrests for seat heating level 3.

Values:

• 42 °C
• 43 °C
• 44 °C
• 45 °C
• 46 °C
• 47 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear seats temperature level 1

The temperature of the rear seats for seat heating level 1.

Values:

• 30 °C
• 31 °C
• 32 °C
• 33 °C
• 34 °C
• 35 °C
• 36 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear seats temperature level 2

The temperature of the rear seats for seat heating level 2.

Values:

• 35 °C
• 36 °C
• 37 °C
• 38 °C
• 39 °C
• 40 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Rear seats temperature level 3

The temperature of the rear seats for seat heating level 3.

Values:

• 40 °C
• 41 °C
• 42 °C
• 43 °C
• 44 °C
• 45 °C
• 46 °C
• 47 °C
• 48 °C
• 49 °C

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat heating automatic activation (2 of 2)

The iDrive system can be used to set the seat heating to be activated automatically below a certain outside temperature. The option “Seat heating front automatic activation (1 of 2)“ and/or “Seat heating rear automatic activation (1 of 2)“ must also be activated in the “Headunit“.

Values:

• All seats
• Driver's seat
• Front seats
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat heating front automatic activation (1 of 2)

The iDrive system can be used to set the front seat heating to be activated automatically below a certain outside temperature. The option “Seat heating automatic activation (2 of 2)“ must also be activated in the “Body Domain Controller“. Please note that a “BDC_BODY2“ or “BDC_BODY3“ is required.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Seat heating rear automatic activation (1 of 2)

The iDrive system can be used to set the rear seat heating to be activated automatically below a certain outside temperature. The option “Seat heating automatic activation (2 of 2)“ must also be activated in the “Body Domain Controller“.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Seat heating/cooling setting memory

The memory duration of the seat heating/cooling settings.

Values:

• 15 minutes
• 24 hours
• Do not save
• Unlimited

Requirements:

• “Seat Module Driver” CFAS_S15 or “Seat Module Passenger” CBFS_S15 control unit

Steering wheel heating automatic activation (1 of 2)

The iDrive system can be used to set the steering wheel heating to be activated automatically below a certain outside temperature. The option “Steering wheel heating automatic activation (2 of 2)“ must also be activated in the “Body Domain Controller“.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Initial seat belt reminder after start

Activate/deactivate the initial acoustic seat belt reminder after the car is started.

Values:

• Active
• Not active

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat belt indicator driver seat

Activate/deactivate the seat belt indicator in the instrument cluster for the driver seat.

Values:

• Active
• Not active

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat belt indicator passenger seat

Activate/deactivate the seat belt indicator in the instrument cluster for the passenger seat.

Values:

• Active
• Not active

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat belt reminder driver seat

Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.

Values:

• Active
• Not active

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

Seat belt reminder passenger seat

Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.

Values:

• Active
• Not active

Requirements:

• “Advanced Crash Safety Module” ACSM_5 control unit
• This coding is only possible with one of the OBD adapters listed here.

G-Meter maximum value

The maximum value displayed in the G-meter for scaling.

Values:

• 0.8 g
• 0.9 g
• 1.0 g
• 1.2 g
• 1.5 g
• 1.8 g
• 2.0 g

Requirements:

• “Headunit” HU_MGU control unit

Sport displays values

The values shown in the sports displays. Please note that, depending on the vehicle, not all displays may work.

Values:

• G-meter, power, torque, oil temperature, boost pressure
• Not active
• Power, torque

Requirements:

• “Headunit” HU_MGU control unit

Steering wheel heating memory

The activation of the steering wheel heating is saved and restored the next time the vehicle is started.

Values:

• 15 minutes
• 24 hours
• Do not save
• Unlimited

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Boot lid opening delay

The delay when opening the boot lid with the remote control. This value can be increased to prevent accidental openings of the boot lid.

Values:

• 0.5 seconds
• 0.7 seconds
• 1 second
• 2 seconds
• 3 seconds
• 4 seconds
• 5 seconds
• 10 seconds
• No delay

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Close tailgate with button in the interior without long press

Enable/disable the closing of the tailgate with the button in the interior without a long press.

Values:

• Active
• Not active

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Close tailgate with the remote control without long press

Enable/disable closing the tailgate without a long press of the button on the remote control.

Values:

• Active
• Not active

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Open tailgate after unlock only

The tailgate can only be opened after unlocking the car with the remote control. Please note that “Tailgate“ has to be selected for the tailgate button in the settings in the iDrive system in the car.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.

Tailgate function remote control

The tailgate function that is triggered when the button on the remote is pressed.

Values:

• Open
• Open and close

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Tailgate function when pulling the button in the interior

The tailgate function that is triggered when the button in the interior is pulled up.

Values:

• Close
• Deactivated

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Tailgate function when pushing the button in the interior

The tailgate function that is triggered when the button in the interior is pushed down.

Values:

• Deactivated
• Open
• Open and close

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Warning sound when closing the tailgate with remote control

A warning signal sounds when the tailgate is closed with the remote control.

Values:

• Active
• Not active

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Warning sound when closing the tailgate with the button in the interior

A warning signal sounds when the tailgate is closed with the button in the interior.

Values:

• Active
• Not active

Requirements:

• “Tailgate Function Module” HKFM2 control unit

Video in motion

Enable video in motion. Please note the instructions displayed after coding.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Video via USB

Enable video playback from USB storage media. Use a backup to revert this coding once it has been applied.

Values:

• Active
• Not active

Requirements:

• “Headunit” HU_MGU control unit

Camera warning

Disable the warning that is displayed when using one of the cameras. Use a backup to revert this coding once it has been applied.

Values:

• Not active

Requirements:

• “Headunit” HU_MGU control unit

Night vision warning

Disable the warning that is displayed when using the night vision camera. Use a backup to revert this coding once it has been applied.

Values:

• Not active

Requirements:

• “Headunit” HU_MGU control unit

Warning at start-up

Disable the warning that is displayed when the iDrive system is started. Use a backup to revert this coding once it has been applied.

Values:

• Not active

Requirements:

• “Headunit” HU_MGU control unit

Welcome Light in darkness only

Enable/disable the activation of the Welcome light in darkness only.

Values:

• Active
• Not active

Requirements:

• “Body Domain Controller” BDC_BODY3 control unit
• This coding is only possible with one of the OBD adapters listed here.